fbpx Enduro Pigmented White Poly | General Finishes

庄园|国际

                                  Enduro Pigmented White Poly

                                  Enduro Pigmented White Poly is a high-solids, pigmented water-based wood finish engineered?for cabinets and millwork. Use only over General Finishes White Undercoat or Stain Blocker. Stocked in Black and White, custom colors are available to wholesale customers upon request. White and Clear can be used as tint bases to achieve endless colors. For non-architectural use.?

                                  Find A Store Compare Similar Products
                                  General Finishes Water Based Pigmented Topcoat Enduro White Poly, Gallon, Satin

                                  Instructions

                                  Step 1: Preparation

                                  All wood projects require preparation sanding. If you skip this critical step, your finish may fail.?

                                  Raw wood?

                                  See our video: How To Prep Sand New Wood

                                  1. Sand?with 120-grit sandpaper followed by 150- or 220-grit.?

                                  2. Remove dust.

                                  New Stained Surface: Do not sand. Apply directly to stained surface.

                                  Existing Finish?

                                  See our video: How to Prepare?Existing Finishes?

                                  1. Scuff clean?with a Scotch-Brite? pad or maroon synthetic steel wool & 50:50 mix of denatured alcohol & water.?

                                  2. Dry?1-2 hours.

                                  3. Sand?lightly with 220-320-grit foam sanding sponge.??

                                  4.?Remove Dust

                                  ?

                                  ?

                                  ?

                                  Step 2: Priming

                                  CAUTION:?Do NOT use any type of clear topcoat over?GF White?Poly, as it may cause yellowing.?

                                  CAUTION: General Finishes Enduro White Poly is engineered to adhere well to raw wood,?General Finishes White Undercoat and General Finishes Stain Blocker.

                                  When working over raw wood,?2 coats of either Stain Blocker or White Undercoat MUST be applied?before applying Enduro White Poly to prevent tannin bleed through and ensure a successful outcome. Both work very well but Stain Blocker will achieve a slightly brighter sustained white.

                                  When working over an existing finish, 2 coats of Stain Blocker?MUST be applied?before applying Enduro White Poly to prevent tannin bleed through, improve adhesion and ensure a successful outcome.?

                                  1. ??????Raw Wood Tannin Bleed-Through is?unpredictable; yellowing can appear immediately or months later?with seasonal temperature changes. Oak, pine, mahogany, and Douglas?fir are particularly prone to bleed-through.?
                                  2. Knots in Wood?tend to bleed and are dense, making paint adhesion a challenge.?Stain Blocker may improve?adhesion and prevent bleed-through.
                                  3. Existing Finishes?Bleed-Through?may be caused by wood tannins, previous stains or aniline dyes, surface contamination, and incompatibility between brands.
                                    ALWAYS apply 2 coats General Finishes Stain Blocker before applying Enduro White Poly over an existing finish for adhesion?and to prevent bleed-through.
                                  4. Non-Wood Surfaces?may be able to take paint if primed first. Primer may improve adhesion over?laminate?and prevent bleed-through from MDF. Metal requires a primer made specifically for metal. Always test first before completing your entire project.

                                  NOTE: Do not tint or use General Finishes Stain Blocker?on projects that will be stored outdoors.

                                  Priming Non-Wood Surfaces for Paint
                                  Always test for adhesion on a hidden area of your project before getting started.

                                  Metal: Enduro Pigmented White Poly?is engineered for wood surfaces, but may adhere to metal, such as aluminum or steel, if a metal primer is applied?first.?

                                  1. Clean the surface well.
                                  2. Apply?primer.
                                  3. Dry 48-72 hours before painting.

                                  Laminate:?Enduro Pigmented White Poly MAY adhere to laminate with a bonding primer; however, we cannot guarantee it. You may?increase your chances of success by abrading the surface.

                                  1. Prep: Deep clean, dry thoroughly, sand with 150- then 180-grit sandpaper, and wipe off dust.
                                  2. Prime: Apply bonding primer, dry 12+ hours before painting.

                                  MDF: Enduro Pigmented White Poly can be applied directly to MDF, but the MDF may cast a brown color if not primed first. Two base coats of white-pigmented shellac-based stain-blocking primer, or Stain Blocker, may prevent bleed-through. Alternatively, one base coat of General Finishes Seagull Gray Milk Paint may block brown tone caused by MDF.
                                  ?

                                  Disclaimer
                                  Although?Stain Blocker is engineered to prevent the most persistent bleed-through when 2 coats are applied, General Finishes cannot guarantee prevention of bleed-through or yellowing on every project. Unknown factors and assiduous bleed-through can impact results. Stain Blocker is the strongest option we are aware of at this time and has performed extremely well in our tests.

                                  Step 3: How To Apply General Finishes Enduro White Poly

                                  CAUTION:?Do NOT use any type of clear topcoat over?GF White?Poly, as it may cause yellowing.?

                                  CAUTION: General Finishes Enduro White Poly is engineered to adhere well to raw wood,?General Finishes White Undercoat and General Finishes Stain Blocker.

                                  When working over raw wood,?2 coats of either Stain Blocker or White Undercoat MUST be applied?before applying Enduro White Poly to prevent tannin bleed through and ensure a successful outcome. Both work very well but Stain Blocker will achieve a slightly brighter sustained white.

                                  When working over an existing finish, 2 coats of Stain Blocker?MUST be applied?before applying Enduro White Poly to prevent tannin bleed through and ensure a successful outcome.?

                                  General Finishes Enduro White Poly Application Steps

                                  1. Watch product overview video here?or?comparison of GF paints and pigmented topcoats here.
                                  2. Stir?to reincorporate solids that have settled to the bottom of the can before and throughout the application process.
                                  3. Thin?as desired?with distilled water; start with 5%, increase up to 10% by volume.?
                                  4. Increase open time, if needed, with up to 5% General Finishes Extender?if allowed by local regulations.?GF?Extender will?improve flow and leveling and increase open time, which is helpful in dry climates.?California Residents:?Adding more than 2% of?GF Extender?will make the products?non-compliant per SCAQMD Regulations. GF assumes no liability for the improper use of these products. ? ?
                                  5. Apply 3 coats. Additional coats will not improve durability.
                                    • Spray application: Before spraying, strain through a medium-mesh filter. Spray wet films at 3-5-mil thickness. HVLP: 1.3mm-1.5mm spray tip, medium air cap.?Verify tip sizes with your equipment supplier.?See our?general guide for spray tip sizes. Keep your gun at a 90°?angle, 6-8" from the surface. On large, flat areas, use wet, even patterns 6-8" wide. For narrow surfaces, reduce the fan pattern to 2-3" wide to reduce overspray.?Overlap each pass 25%?to conceal lines. Wear a mask and work in a ventilated space. Read here for more?information on spraying techniques.
                                    • Face frames: Enduro professional products are engineered to be spray-only but can be successfully applied successfully to cabinet face frames, edges or drawer fronts with a small cabinet-specific 3/8" nap microfiber?roller such as?Whizz or AllPro brand. Larger areas may not level with a roller application. Add 10-20% Extender for improved results.?
                                  6. If a faster build is desired over raw wood, use General Finishes Sanding Sealer for?the first coat, followed by 2 coats of White Poly.
                                  7. Dry time?in ideal conditions: 70°F/20°C; 50-70% humidity.?Tack free 5-10 minutes. Ready to sand 30-45 minutes. Recoat in 1-2 hours.?Be sure?to allow adequate dry time.?You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a fine-grade (220-320) foam sanding pad. If in doubt, wait longer. Rushing the dry time can cause "blush," which is clouding in the finish due to moisture trapped between the layers. Increase dry time if:
                                    • Humidity is over 80%
                                    • 3+ coats are applied
                                    • Thick coats are applied
                                    • Applying over an existing sealed finish
                                    • Applying over products from other brands
                                    • Layering General Finishes water- and oil-based products:
                                      • Water over oil: Let oil-based products dry 72+hr before applying water-based?products
                                      • Oil over water: Let water-based?products dry 24+hr before applying oil-based products
                                    • To accelerate dry time in humid conditions, add General Finishes Accelerator and work in a space with good ventilation and air movement. If you decide to re-coat before the recommended time, test dryness.
                                  8. Finish sand between coats with a fine-grade (220-320) foam sanding pad?to improve smoothness and adhesion.
                                  9. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
                                  10. A topcoat is not required.

                                  Cure Time
                                  Water-based finishes cure and harden for full use after 21 days in ideal conditions. Avoid placing heavy objects on surfaces that have not completely cured. Treat gently, and do not clean with commercial products during the curing period.

                                  Warning:?Do not use water-based products with Linseed Oils or Danish Oils.

                                  Cleanup of Water Based Products

                                  Application tools and materials?containing water-based products can be cleaned?with soap and water immediately after use.

                                  Product Spills
                                  Spills may be able to be removed from fabric and carpet if cleaned immediately with soap and water.

                                  Storage of Water Based Products

                                  Please be mindful of the manner in which water-based products are?stored and how?long they have?been in storage.?They not a forever product.?
                                  ?

                                  Life of Product
                                  Water-based products do not last forever, even when unopened. General Finishes products are best used within 1 year of the manufacture date listed on the can.?However, the life of the product may be extended with proper care and storage (see Storage Tips below).

                                  Water-based products can?last 3-5 years if?the can is unopened, in good condition?and stored in correct temperatures.

                                  Product that is 3 years old will not look like product that is 6 months to 1 year old. You will see more stratification?or?separation as the product ages. Always stir?thoroughly before using.?


                                  Foul?Smell
                                  If your product?has a foul smell, it?is contaminated and?no longer in useable?condition.


                                  Clumps & Settling
                                  Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older product?stir with a?paint mixing attachment on a drill.

                                  If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use.

                                  Inability to reincorporate large, chunky lumps after?stirring for several minutes?is an indication that the product has frozen and can no longer be used.


                                  Storage Tips
                                  See video tutorial: Tips on Storing Leftover Finishes
                                  Water-based finishes crystalize and form a skin?due to evaporation when the air-tight seal on a can is broken at first use. The following best practices will increase the life of your product:

                                  1. Pry open sealed lids with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal.?
                                  2. Keep lid closed while working. Pour what you will use into a bowl, paper cup, or plate, and close can lid as you work.
                                  3. Clean the chime of the can?thoroughly with a paper towel before closing to create a complete?seal. Product falling?into the chime can?be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
                                  4. Pound the lid in place?using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
                                  5. Store in moderate temperatures.?Avoid temperatures below 50°F/10°C or above 100°F/26°C. Keep from freezing. Frozen and heat-damaged product cannot be revitalized. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next to something warm like a water heater or furnace.
                                  6. Store can upside down to create a liquid seal, minimize evaporation and reduce the chance of?crystallization.?Decant remaining product from the can before stirring.?
                                  7. Decant leftovers to a smaller container when the?finish is almost used up. Alternative storage containers for water-based products are plastic FIFO bottles or glass bottles. Do not fill metal-lidded containers completely to prevent them from rusting.


                                  The following water-based product mixtures?can be stored:

                                  1. Product thinned with up to 15% General Finishes Extender or General Finishes?Accelerator can be stored, with the exception of thinned?General Finishes Water Based Wood Stain.
                                  2. Mixtures involving colors & sheens within the same product line, such as:
                                    • High Performance Satin + High Performance Gloss
                                    • Snow White Milk Paint + Coastal Blue Milk Paint
                                    • Amber Dye Stain + Merlot Dye Stain


                                  The following product mixtures?should NOT be stored:

                                  • Any water based product with thinned tap water; water often contains bacteria that will adversely affect stored paint.
                                  • Topcoat + Stain or Paint
                                  • Milk Paint + Chalk Style Paint
                                  • Water Based Wood Stain + Dye Stain

                                  Furniture Care and Maintenance

                                  Cure First
                                  You have just finished applying a fine furniture finish. Treat gently until the paint or topcoat have fully cured. Allow 21 days for a water-based?finish to cure and 30 days for an oil-based finish to cure before cleaning.

                                  Regular Cleaning and Maintenance

                                  • Remove dust?with a water-dampened cloth. Dust can build up over time and may scratch or dull finishes if not removed regularly.?
                                  • Remove fingerprints, cooking fumes and smoking residue with mild soap and water. These contaminants will not harm the finish, but they accumulate on surfaces and dull the original luster.?
                                  • As with all fine furniture finishes, avoid using?furniture polish, cleaners or dusting sprays that contain silicone, alcohol, ammonia and anything acidic.?Exception: We have successfully cleaned with Clorox wipes.
                                  • Clean up water, alcohol and food spills in a timely manner and use placemats & coasters to?protect the finish.
                                  • Future finishes or touch-ups may not adhere properly or perform as desired over a contaminated surface.?Some contaminants, such as silicone, seep through finish into the wood and often cannot be removed.
                                  • Avoid excessive exposure to direct sunlight, high temperatures?or high humidity. These?can damage furniture and finishes.

                                  Warnings and Warranties

                                  Compatibility
                                  Do not use water-based products with Linseed Oils or Danish Oils.

                                  Limited Warranty
                                  General Finishes products must be tested to your complete satisfaction before using. General Finishes will not be responsible for color satisfaction, misapplication, nor compatibility with other manufacturers' products. General Finishes will be responsible only for the cost of our products, and not for costs such as labor, damage or project replacement.?

                                  Contamination and Compatibility
                                  Our finishes are engineered as a system and are compatible with each other. General Finishes cannot guarantee an ideal refinish when applying our products on top of or combined with another company's products or over surfaces that have been in contact with waxes, polishes or sprays containing contaminants such as silicone. Test for adherence and aesthetics before beginning.?

                                  Warning
                                  If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log onto www.epa.gov/lead.

                                  FIRST AID:
                                  Seek immediate medical attention if symptoms occur due to the following. EYE CONTACT: Remove any contact lenses. Flush eyes with water for 20+ minutes while lifting upper and lower eyelids. SKIN CONTACT: Wash thoroughly after handling. INHALATION: Move to fresh air and loosen clothing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. INGESTION: Call physician immediately. Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.?

                                  Warning
                                  This product contains a chemical known to the State Of California to cause cancer and birth defects. Do not swallow; first aid: drink water to dilute product. May cause eye or skin irritation; first aid: flush eyes thoroughly with water.

                                  Warning
                                  Keep out of reach of children. Avoid contact with eyes. Keep container tightly closed when not in use. Wash thoroughly after handling.

                                  Specifications

                                  Basic Features
                                  Product Colors White
                                  Base Type Water
                                  Sheen Flat (10 or less), Satin (25-35), Semi-Gloss (50-60)
                                  Interior or Exterior Interior only
                                  Type Urethane/Acrylic Blend
                                  Application
                                  Coats 3 coats
                                  Application Method Spray
                                  Brushable No
                                  Usable over existing finishes Yes - see product page application instructions.
                                  Sprayable Yes
                                  Spray Tip Sizes HVLP 1.3mm-1.5mm
                                  Dry Time
                                  Dry Time - Touch 30+ min.
                                  Dry Time - Recoat 2+ hr
                                  Dry Time - Light Use 7-10 days
                                  Dry Time - Cure 21 days
                                  Contents
                                  Can Sizes Gallons, 5 Gallon pails, 55 Gallon drums
                                  Coverage 450 sq. ft/gal
                                  Technical Data
                                  Viscosity Medium
                                  Viscosity (cPs) 600-800
                                  Weight Solids 44%
                                  VOC US VOC
                                  Flat: 185.516 g/L
                                  Satin: 186.453 g/L
                                  Semi-Gloss: 209.366 g/L
                                  Durability
                                  Durability (Highest, High, Medium, Low) High
                                  Hardness (Koenig #) 59
                                  Wear (Taber #) 109.80 mg loss
                                  Water (5 max) 5
                                  Chemical (105 max) 88

                                  FAQs

                                  *What Is the Best Way to Store Water Based Finishes?

                                  LIFE OF PRODUCT
                                  Water-based?products do not last forever, even when unopened. General Finishes products are best used within 1 year of the manufacture date?listed on the bottom of the can. The life of the product may be extended?to 2-3 years with proper care and storage.

                                  SETTLING
                                  Gravity can cause some solids to settle on the bottom of the can and slight separation on the top. This is normal. If working with older paint, use paint mixing attachment on a drill. If the solids dissolve and clumps smooth out after mixing from the bottom, the product is in good condition for use.

                                  STORAGE TIPS
                                  See video tutorial:?Tips on Storing Leftover Finishes
                                  Water-based finishes crystalize and form a skin?due to evaporation when the air-tight seal on a can is broken at first use. The following best practices will increase the life of your product:

                                  1. Pry open sealed lid(s) with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal.?
                                  2. Keep lid(s) closed while working. Pour what you will use into a bowl, paper cup, or plate, and close can lid as you work.
                                  3. Clean the chime of the can(s) thoroughly with a paper towel before closing to create a complete?seal. Paint in the chime can?be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
                                  4. Pound the lid(s) in place?using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
                                  5. Store in moderate temperatures.?Avoid temperatures below 50*F/10*C or above 80*F/26*C. Frozen and heat-damaged product cannot be revitalized. Temperature-controlled spaces, such as a basement, are ideal for storage. Do not store product in an attic, garage, in direct sunlight, or next to something warm like a water heater or furnace.
                                  6. Store?the can(s) upside down to create a liquid seal, minimize evaporation and reduce the chance of?crystallization.?Decant remaining product from the can before stirring.?
                                  7. Decant leftovers to a smaller container when the?finish?is almost used up. Alternative storage containers for water-based products are plastic FIFO bottles or glass bottles. Do not fill metal-lidded containers completely to prevent them from rusting.

                                  The following water-based product mixtures?can be stored:

                                  1. Product thinned with up to 15%?General Finishes Extender?or?General Finishes?Accelerator?can be stored, with the exception of thinned?General Finishes Water Based Wood Stain.
                                  2. Mixtures involving colors & sheens within the same product line, such as:
                                    • High Performance Satin + High Performance Gloss
                                    • Snow White Milk Paint + Coastal Blue Milk Paint
                                    • Amber Dye Stain + Merlot Dye Stain

                                  The following product mixtures?should NOT be stored:

                                  • Any water based product with thinned tap water; water often contains bacteria that will adversely affect stored paint.
                                  • Topcoat + Stain or Paint
                                  • Milk Paint + Chalk Style Paint
                                  • Water Based Wood Stain + Dye Stain

                                  Related Products

                                  Relevant Videos

                                  *Why Do I Sometimes Get Metal Marks On Cabinets I Have Painted with White Poly?

                                  This is very common in pigment coatings and paints. Is called metal marking and it is a characteristic that is very difficult to eliminate. You can even see it in dinnerware like white plates. We usually test with wedding rings and forks. It a constant focus and improvement project for General Finishes, especially the whites. The difference with tinted clear is that the amount of pigment varies from color to color, so sometime it will occur?with the lighter paints.

                                  How Do General Finishes Water Based Topcoats Differ?

                                  GF?recommends using the least expensive product that will provide the needed performance characteristics. We offer a range of products designed for professional spray applications and brush-on finishes for consumer use.

                                  Compare all GF Topcoats Here

                                  Watch Video: Comparison of All GF Water Based Finishes Here

                                  PROFESSIONAL TOPCOATS

                                  PRE CAT LACQUER (Spray only)

                                  GF recommends our recently improved Pre Cat Lacquer for applications where there is little risk of chemical contamination issues from substances such as ketchup, soap, chemical cleaners, or ammonia. This is the perfect spray finish for interior doors, casing, moldings, door jambs and furniture that receives light use. When you think about it, interior doors don't take a lot of wear. You might wipe them down or dust them once in a while but that is about it. PreCat Lacquer is a hard finish that provides excellent build and superior clarity at a phenomenal price point. If you are not finishing a surface such as a table top where you anticipate chemical contamination during use, why pay for a more expensive finish?

                                  Dries clear.

                                  Watch Pre Cat Lacquer Product Overview Video Here

                                  CLEAR POLY (Spray only)

                                  Poly is the go-to cabinet finish. It has all the durability you need at a lower price point than Conversion Varnish. It is similar to High Performance in test measurements for chemical, water and wear resistance, but HP can be brushed and Clear Poly can't - it is already thinned for spraying. Clear Poly has a bit of an edge over High Performance in overall chemical resistance, a 98 rating vs 92.

                                  Dries clear.

                                  Watch Clear Poly product overview video here

                                  CONVERSION VARNISH (Spray only)

                                  This is our top of the line. Conversion Varnish is a post catalyzed high solids, two component urethane formulated for professionals who need the highest level of durability and chemical resistance. Varnish will cure the fastest. Requires NCO Catalyst. It is recommended for commercial applications or extremely high-wear surfaces such as?countertops and bar tops

                                  Dries clear.

                                  Watch Conversion Varnish Product Overview Video Here

                                  RETAIL TOPCOATS

                                  HIGH PERFORMANCE (Brush or Spray)

                                  GF's best performing brush on finish with very similar performance testing as our Poly. (High Performance can be thinned for spraying).

                                  Dries clear.

                                  Watch High Performance Product Overview Video Here

                                  FLAT OUT FLAT (Brush or Spray)

                                  Flat Out Flat is formulated with a self cross-linking acrylic, and is designed to mimic the look and feel of a wax finish. Because of the increased matting agents used to create the "Flat look", this finish will have less clarity. ?Like wax, it dries softer to the touch than High Performance when completely cured, and will show more fingerprints. FOF finish will mark up more easily because of increased matting agents used to reduce the sheen, so it is not recommended for high-use tabletops.

                                  Dries clear.

                                  Watch Flat Out Flat Product Overview Video Here

                                  BOTH PROFESSIONAL AND RETAIL TOPCOATS

                                  ENDURO-VAR (Spray or brush)

                                  Enduro-Var is an oil modified water-based alternative for customers that want the warm look of an oil finish in a water based coating.?It looks more like an oil finish than a water coating, and can be sprayed or brushed. Enduro-Var adheres well ONLY over WATER STAINS, DYE STAINS, and RAW WOOD. Use over other finishes at your own risk.

                                  Dries Amber

                                  Watch Enduro-Var Product Overview Video Here

                                  EXTERIOR 45O TOPCOAT

                                  Exterior 450 provides a clear drying tough, protective finish that will withstand the rigors of the sun, rain, and wind. It is suitable for vertical surfaces such as fences, patio furniture, garage doors, entrance doors, outdoor kitchens and interior windows. It is not recommended as a deck finish. Fortified with UV absorbers to stabilize the finish, Exterior 450's built-in mildewcide retards mold and mildew growth.

                                  Dries Clear

                                  Watch Exterior 450 Topcoat Overview Video Here

                                  ?

                                  Which Topcoat Should I Choose?

                                  General Finishes Water Based Topcoats:

                                  • High Performance
                                  • Flat Out Flat
                                  • Enduro-Var
                                  • Enduro Clear Poly
                                  • Enduro 2K Conversion Varnish
                                  • Enduro Pre-Cat Lacquer
                                  • Exterior 450

                                  General Finishes Oil Based Topcoats

                                  • Arm-R-Seal?
                                  • Gel Satin Topcoat
                                  • Wood Bowl Finish
                                  • Butcher Block Oil
                                  • Outdoor Oil

                                  GENERAL PRACTICE:

                                  1. Oil based topcoats and Enduro-Var will amber over time.
                                  2. Water based Flat Out Flat and High Performance top coats dry clear.
                                  3. Never use any water based topcoat with long oils such as Danish, Tung or Linseed.
                                  4. Water based top coats clean up with water. OIl based topcoats require mineral spirits for clean up.
                                  5. Enduro-Var ADHERES WELL only over WATER STAINS, DYE STAINS, and RAW WOOD.
                                  6. If you use water based topcoats over oil based finishes, make sure that you wait 72 hours between the two products. It is essential to let the oil finish dry longer.
                                  7. For more complex projects that have a lot of nooks and crannies or projects with large surface areas such as cabinets, we recommend either ARM-R-SEAL liquid oil based topcoat or any of our water based topcoats. Large surfaces such as cabinets or tables and complex projects with lots of detail are easier to cover with liquid topcoat rather than a Gel top coat.
                                  8. Enduro Professional Topcoats are thinner and intended to be sprayed
                                  9. High Performance and Flat Out Flat can also be sprayed. If needed, it can be thinned by adding 5-10% distilled water.?

                                  Compare all topcoats


                                                                    education

                                                                    Variety show

                                                                    news

                                                                    mailbox

                                                                    Variety show

                                                                    game

                                                                    Foreign exchange

                                                                    Technology

                                                                    news